Arung arai masat masa ni
|
PARAMETER |
JAW AI VOLTAGE |
TSAWN GA |
|
3.3V |
||
|
Kalang lang lang ai |
10 ~ 40MHz |
-- |
|
Kalang lang hkam sharang lu ai |
±200ppb |
Shawng nnan na tol.@+25 degree |
|
Frequency ngang grin ai lam |
±5ppb/20ppb/±50ppb |
Table lawu na note hpe yu u. |
|
Bungli galaw ai nbung n-gun |
−20 kaw nna +70℃/ −40 kaw nna +85 degree |
Lahta na stabilities ni hpe hpawng de ai. |
|
Laning mi hta asak kaba wa ai |
±0.6ppm |
@+25 janmau |
|
Hprawng wa ai waveform hte load |
CMOS 15pF |
-- |
|
Shapraw ai wan n-gun madang HIGH |
2.4 |
N law htum |
|
Shapraw ai wan n-gun madang LOW |
0.4 |
Grau htum |
|
Rise hte Fall aten ni |
8ns |
Vcc a @10~90% |
|
Symmetry (lit magam shingjawng ai lam) |
45~55% |
@ 50%Vcc |
|
Phase nsen (ga shadawn 10MHz) |
-125dBc/Hz / -145dBc/Hz / -150dBc/Hz |
@100Hz/1kHz/10kHz |
|
Lahta na jitter RMS |
<1ps |
12kHz Fj hta n law ai (sh) maren sha 20MHz hta n law ai (sh) maren sha re |
|
N-gun jai lang ai lam (katsi ai) (n-gun rawng ai masa) |
1.5w |
Max |
|
0.4w |
Max |
|
|
Matsing ai:Frequency stability ngu ai gaw +25℃hpe madung tawn nna, nbung katsi ai shara hta na nbung laru n bung ai lam re. |
||
Product a laklai ai lam ni
■ Kaji ai 9.7x7.5x4.1 hte 4 lang n-gun rawng ai
■ Katsi kahtet ai shara hta ngang kang ai ngang grin ai lam
■ RoHS hte maren hkan sa ai, LEAD-N AI
Laika shawk shawn ai lam ni
- OS97H4 series gaw SC-Cut Oven-Hkang ai Crystal Oscillator (OCXO) rai nna, n-gun ja ai n-gun ja ai bungli ni rai nga ai, Robot Servo System hte hpyen radar ni a matu galaw da ai re.
Product a akyu ni
N-gun ja ai
Shi gaw laklai ai ngang grin ai lam hpe jaw ya ai-dai hpe billion mi hta daw (PPB)- hku nna shadawn nna, hkrak tup ra kadawn ai lam ni hpe hkan sa na matu gram lajang mai ai.
Kaji ai htinggaw kaba ai
9.7x7.5mm form factor hpe kaji hkra galaw da ai gaw, n-gun n law ai arung arai hkrang shapraw ai lam ni a matu ahkyak ai lam langai rai nna, kaji ai hte grau hpawng de da ai electronic system ni a matu ra kadawn ai lam law wa ai hpe hkrak sha hparan ya lu ai.
sakse laika
SC{0}}Cut CMOS OCXO 9.7 x 7.5 OS97H4 gaw RoHS hte maren rai nna, n-gun n rawng ai.
FAQ
Q1: OCXO langai a kata lam gaw hpa rai ta?
A: OCXO langai a madung daw ni gaw:
1)Crystal Resonator: Ga law malawng gaw SC-cut (sh) AT{2}}cut quartz nlung hpe lang nna, nbung katsi ai shara hta ngang grin ai hku galaw lu ai majaw lata la ai.
2)Heating Element & Oven Chamber: Katsi ai hpe n galai shai ai sha, kata na katsi ai hpe n galai shai ai sha tawn da na matu, katsi ai hpe n-gun n jaw ai shingnip (ga shadawn, n-gun n rawng ai wire) hte katsi ai hpe chye na lu ai jak (ga shadawn, thermistors) ni lawm ai.
3)Temperature Control Circuit: Sensor data hpe madung tawn nna, n-gun hpe hkrak hkrak n-gun n-gun hpe gram lajang ya ai feedback loop langai mi re.
4)Oscillation Circuit: N-gun n-gun hpe shapraw ya ai, law malawng gaw Phase nsen hpe shayawm na matu n-gun jat bang ai.
5)Thermal Insulation Layer: Katsi ai hpe shayawm ya nna, n-gun jai lang ai lam hpe mung shayawm ya ai.
6)Voltage hpe hkang ai: Oscillator hte heater hpe ngang grin ai n-gun jaw ya ai.
Ndai yak hkak ai hkrang gaw OCXO ni hpe nbung laru kaba (-40℃kaw nna +85℃) hta ultra-low frequency drift (±0.1–10 ppb) hpe lu la shangun ai majaw, grai hkrak hkra galaw ra ai application ni a matu grai kaja ai, 5G hpyendap dap ni, nbungli dap ni, hte.
2:7 x 7.5 OS97H4 series a matu SPQ gaw hpa rai ta?
A: 250/Reel hpe lang ai.
Hot Tags: 9.7 x 7.5, Miwa mung na sc{3}}cut cmos ocxo 9.7 x 7.5 galaw shapraw ai ni, dut ya ai ni
